Design of Circularly-Polarized Patch Antennas using CST MICROWAVE STUDIO®
A reader is a radio frequency (RF) transmitter and receiver, controlled by a microprocessor or digital signal processor. The reader, using an attached antenna, captures data from tags then passes the data to a computer for processing. Here the design flow of a patch RFID-antenna for frequency range: 908.5 - 914 MHz (RFID band of Korea) using CST MWS is described. This article is published with the permission and courtesy of Prof. Bierng-Chearl Ahn and his colleagues at Chungbuk University, Korea.
Figure 1 shows the proposed structure of the antenna and the design parameters.
Figure 1: Deasign parameters of RFID-antenna.
The design parameters define the operation and the performance of the antenna. The operating frequency determines the size of the patch antenna: W ≈ L = 0.4 λ, while truncation t / W, as well as vertical height of the ground plane, the axial ratio. The ground plane size controls the gain of the antenna while the distance between ground plane and the patch affects the bandwidth. On the other hand, the size of the feed gap influences the impedance matching. The geometry was drawn and the parameters of the antenna optimized through simulations performed in CST MWS. Figure 2 whows the CST MWS model of the patch antenna, the final design parameters and the manufactured antenna.
Figure 2: The geometry of the patch antenna seen in CST MWS together with fabricated one.
The measurements were made and compared with the simulations. The plots of the reflection coefficient and the gain are shown in Figure 3. It can be seen that the measurement results agree with the simulations very well.
Figure 3: Comparison results between measured and simulated values. All simulations were performed in CST MWS.
The patch antenna was further miniaturized by placing dielectric material between the patch and the ground. The simulated and consequently fabricated miniaturized antenna can be seen in Figure 4 with the final design parameters.
Figure 4: RFID patch antenna miniaturized by dielectric loading.
The simulations are compared to the measurements in Figure 5. It can be seen that with the dielectric between patch and the ground, the better resonance at frequency of 900 MHz can be achieved.
Figure 5: Simulation and measurement results for the antenna with dielectric.
As the last step the gain was increased via designing 2-Element SFADP Array. First, the distance between elements was optimized using CST MWS in order to obtain maximum gain. After that the feeding network and power divider circuit (Figure 6) were designed.
Figure 6: Feeding network and power divider.
The antenna array was manufactured and measured. The comparison plots between measurements and simulations can be seen in Figure 7 and 8.
Figure 7: Performance of the designed antenna.
Figure 8: Performance of the designed antenna: axial ratio.
In this article three RFID reader antennas were designed using CST MWS. Measurements of the fabricated antennas show good agreement with simulated results.
CST Article "Design of Circularly-Polarized Patch Antennas using CST MICROWAVE STUDIO®"
last modified 8. Feb 2006 3:06
printed 4. Jul 2008 3:32, Article ID 245
URL:
All rights reserved.
Without prior written permission of CST, no part of this publication may be
reproduced by any method, be stored or transferred into an electronic data processing system, neither mechanical or by any other method.
Article ID: 245
Last modified: 8. Feb 2006 3:06
Other Articles
For a customer given corrugated horn the phase center has been computed using CST MICROWAVE STUDIO® and compared with measurement data. The simulated results are in very good agreement with measurements. Measurements were provided with courtesy and permission of Kathrein Werk KG, Rosenheim, Germany.
Read full article..
This article concerns the application of CST MICROWAVE STUDIO® (CST MWS) to the simulation of electrically large automotive structures. CST MWS is ideal for such applications since the geometry can be easily imported and modified using the powerful user interface, the accurate and robust PERFECT BOUNDARY APPROXIMATION (PBA)® approximation is exploited, the linear scaling of memory with increasing mesh cells and the ability to simulate broadband in one single simulation. An example of an on-glass antenna simulation is also demonstrated highlighting the versatility of the CST MWS Transient solver.
Read full article..
This article deals with the simulation of the voltage drop for complex power delivery networks. Such a simulation is useful to the design engineer in order to ensure power integrity. With the help of the CST EM STUDIO™ stationary current solver the 3D distribution of the potential and current density on all layers of a complex PCB board can be easily determined. The static IR-Drop simulation is the primary focus in this article but a dynamic simulation would also be possible in CST MICROWAVE STUDIO®.
Read full article..
This article describes the design flow for a high speed connector using different simulation tools. The goal is to enable a first pass design without time-intensive and costly iteration steps. In addition to other simulation tools, CST MICROWAVE STUDIO® (CST MWS) is used during different stages of the design process to find fundamental design parameters and to predict the behaviour of a complete telecommunication system.
Read full article..
A standardized spherical phantom head such as the one described in this example is commonly used for SAR investigations and measurements.
Read full article..