X-Band Squintless Horn Antenna Array (96 elements)
Reutech Radar Systems (Pty) Ltd recently required a new antenna for an X-Band radar system and the design of a full plank of the receive antenna was performed using CST MICROWAVE STUDIO® (CST MWS). Typical design requirements have been vertical polarisation, 70º elevation beamwidth, 1º azimuth beamwidth with 30dB sidelobe levels, no squint and 20% operating bandwidth. The first two requirements are met by using a small E-plane sectoral horn shown in figure 1.
Figure 1: E-Plane horn
The azimuth properties of the antenna must be met by the design of the antenna feed. A 12-way squintless wideband waveguide E-plane divider section (see figure 2), based on a feed described by A Rogers [1], has been used as building block for the feed.
Figure 2: E-plane divider building block
An impedance transformer and 90º waveguide twist section are required to match the feed to the E-plane sectoral horn radiator. A machineable waveguide twist section consisting of L-shaped waveguide, similar to that published by Lenzing and Gans [2], is used to change the polarization from horizontal to vertical.
Figure 3: Twisted waveguide section
To evaluate the design approach, a prototype sub-antenna consisting of a 12-way feed, twist sections and E-plane horns was manufactured from Aluminium using CNC-machining and wire-cutting. The gain patterns were measured in the anechoic chamber at Stellenbosch University and are in good agreement with the expected results given by CST MICROWAVE STUDIO®.
Figure 4: Manufactured 12-element antenna
The design was then extended to a 2.4 meter full antenna plank with 96 radiating elements. For the excitation distribution the 96 elements were divided into 16 banks with a Villeneuve distribution. Each of the banks contains 6 elements with a linear excitation distribution. Such a distribution allows for the reuse of 6-way E-plane dividers throughout the antenna feed.
Figure 5: Full antenna blank with 96 radiating elements
The final feed consists of four levels of 3-port E-plane dividers connected with standard X-band waveguide. Since the feed structure is symmetrical, in a first step only half of the feed was analysed in CST MICROWAVE STUDIO®.
Figure 6: CST MWS model of one-half of full antenna bank
Figure 7: Magnitude of frequency response (half design)
Figure 8: Phase variation between channels (half design)
The complete antenna (with 96 ports excited at the same time) was also analysed in CST MICROWAVE STUDIO®, giving the following azimuth gain patterns.
Figure 9: Excitation and phase pattern used for the 96 elements
Figure 10: Azimuth patterns from full plank CST MWS analysis
The full antenna plank was manufactured and the radiation patterns were measured at the compact range at the University of Pretoria.
Figure 11: Compact range measurement setup at University of Pretoria
Figure 12: Measured azimuth pattern
Figure 13: Measured azimuth pattern
The azimuth radiation patterns show that no side-lobes higher than –30dB are measured outside ±20º from the main lobe. Some larger close-in side-lobes exist, which can be seen more clearly in figure 13. The highest side-lobe level is measured as –23dB at 10GHz. The 3dB beam-widths of the azimuth patterns vary from 1.2 to 0.8º over the frequency range. This corresponds very well with the expected results.
References
[1] A Rogers, “Wideband Squintless Linear Arrays”, The Marconi Review, Volume XXXV, Number 187, Fourth Quarter 1972, pp 221 – 243.
[2] H. F. Lenzing, M. J. Gans, “Machined Waveguide Twist”, IEEE Trans. MTT, Vol. 38, no. 7, July 1990, pp. 942 – 944.
CST Article "X-Band Squintless Horn Antenna Array (96 elements)"
last modified 9. Jan 2008 4:39
printed 4. Feb 2012 11:34, Article ID 352
URL:
All rights reserved.
Without prior written permission of CST, no part of this publication may be
reproduced by any method, be stored or transferred into an electronic data processing system, neither mechanical or by any other method.
Article ID: 352
Last modified: 9. Jan 2008 4:39
Other Articles
The TEAM Workshop Benchmark Problem no. 8 - Coil above a crack - is solved with CST EM STUDIO™. Results are compared with measurements.
Read full article..
Marcello Zolesi, Thales Alenia Space
The scope of the present work is to analyze the effective coverage of TT&C subsystem of a LEO satellite at an altitude of 700 kilometres. The antenna assembly is made of two units, Main and Fill-In Antennas, accommodated on opposite sides of the spacecraft. Starting from the free-space radiation performance of each of the two antennas, the problem to predict the global TT&C subsystem radiation pattern in presence of the spacecraft is treated in order to identify potential blind areas or interferences caused by the neighbouring structures. The prediction of electromagnetic field scattered in complex environment is usually a hard task since the solution cannot generally be expressed in a simple and/or closed analytical form. Therefore a variety of numerical methods have been developed in literature. The effectiveness of a single method depends on the type of the electromagnetic environment and the working frequencies. The calculations of the global TT&C subsystem radiation pattern in presence of the main spacecraft structures are carried out by means a full-wave electromagnetic software, CST Microwave Studio Integral Solver. The Integral Solver is ideally suited for electrically large structures respect to the wavelength, when dominated by electrical conductors. This solver uses a combination of an open boundary integral formulation and a Multilevel Fast Multi-Pole Method (MLFMM) exhibiting an optimal complexity in terms of memory and simulation time compared to the traditional Method of Moment (MoM). Key-words: Coverage, EIRP, MLFMM, MoM, TT&C antennas.
Read full article..
K. Carrigan, Senior Systems Engineer, U.S. Navy (NSWC Dahlgren), & D. Johns, CST of America. Video of a webinar presentation (Running time: 32 min).
Read full article..
An RFID Reader Antenna with the following specifications was designed:
- Frequency: 908.5 - 914 MHz (In Korea)
- VSWR: less than 2 with 50-ohm impedance
- Polarization: circular
- Axial ratio: less than 3 dB @ 908.5 - 914MHz
- Gain: 6 dBi @ 1W transmitted power
- Size and weight: as small as possible
This article is published with the permission and courtesy of Prof. Bierng-Chearl Ahn and his colleagues at Chungbuk University, Korea.
Read full article..
Radio Frequency Identification Systems (RFID) are widely used and allow advanced solutions for a variety of applications in the area of authentication, ticketing, access control, supply management, parking, payment, vending,etc. The example presented here is a RFID Readercoil "P81" from Legic Ident Systems and was modeled and solved using the frequency domain solver of CST MICROWAVE STUDIO® (CST MWS). The sensitivity of the computed complex input impedance with respect to substrate tolerances is computed and was compared to measurement data.
Read full article..