CST – Computer Simulation Technology
Getting Ahead with the Interference Task
The Interference Task in CST Studio Suite® is a system-level tool for the simulation of RF interference and receiver desense. It can be used to analyze inter-systems and intra-system coupling and delivers information about the possible occurrence of RF interference at a glance. The Interference Task is fully integrated into CST Studio Suite, making it easy to run different scenarios and test mitigation strategies.
In this eSeminar we will present all steps necessary to perform the simulation of RF interference and explain the concepts behind the tool:
- Introduction to the analysis method.
- Definition of a coupling matrix for interference analysis.
- Definition of RF systems from building blocks like receiver and transmitter.
- Analysis of simulation results.
- Advanced source definition using schematic simulation....
Presenter
- Ilari Hänninen
- holds a Doctor of Science degree in electrical engineering from Aalto University, in Helsinki, Finland. Since 2008 he works for CST - Computer Simulation Technology AG in Darmstadt, Germany, as a Principal Engineer. His focus is on frequency domain solution methods for electromagnetic simulations and his interests also include large scale electromagnetic simulations and high performance computing.
-
Mod
-
Mod
-
-
New Features for EDA & EMC/EMI Workflows in CST Studio Suite 2016
This eSeminar will demonstrate the new features and tools available in CST Studio Suite® 2016 and its use in EDA and EMC applications. We will show how an integrated EM simulation approach can help improve the design of individual components, packages...
-
Jitter Compliance of SerDes Channel
As the data rate increases for SerDes channels, signal integrity becomes increasingly important in the design process and the signal must continue to pass the jitter compliance test. In this eSeminar, we will present the jitter calculation methodology...
-
Multiphysics Simulation for Integrated PCB Design and Operation Environment Analysis
Increasing demands for Print Circuit Boards (PCBs) to have more versatile functions, higher speeds and smaller footprints pose significant challenges to their design. This eSeminar focuses on how a holistic simulation approach can allow designers to identify...
-
Getting Ahead with Antenna Magus 2015
In this eSeminar, we will explore some of the ways in which Antenna Magus can be used in conjunction with CST Studio Suite® to help antenna designers and system engineers deal with antenna-related tasks. Examples will also be shown of the capture of specification...
-
New Features for Microwave and RF Simulation in CST Studio Suite 2015
CST Studio Suite 2015 introduces several new features for the simulation of both individual components and full systems. This eSeminar will demonstrate new workflows that allow components and systems to be designed, simulated, analyzed and optimized efficiently.
Related Videos
-
Electrical Fast Transient Burst (EFT B) Susceptibility of an LV Circuit Breaker
The coupled voltage at component level has been simulated using CST MICROWAVE STUDIO SUITE® for two PCB releases of the same Low Voltage Circuit Breaker (LV-CB) electronic control scheme. The results show a good agreement with actual measurements.
-
RFID Reader-Coil, 13.56 MHz
Radio Frequency Identification Systems (RFID) are widely used and allow advanced solutions for a variety of applications in the area of authentication, ticketing, access control, supply management, parking, payment, vending,etc. The example presented...
-
A Dielectric Lens Antenna with Enhanced Aperture Efficiency for Industrial Radar Applications
A well-focused antenna with a narrow beamwidth is required for measuring the tank filling level in an industrial storage tank. A dielectric lens antenna has been developed for this application using simulation with CST MICROWAVE STUDIO® and achieving...
-
Modeling and Measurement of Shielding Enclosures
The shielding effectiveness (SE) of an enclosure has been simulated by using CST MICROWAVE STUDIO® (CST MWS) and then compared to measurement from a known reference case. Despite the fact that the shielded enclosure was simulated neglecting many details,...
-
Optimization of Torque in a Permanent Magnet Synchronous Motor (PMSM) for Traction Applications
This article summarizes the simulation and optimization of a Permanent Magnet Synchronous Motor (PMSM) commonly used for traction in automotive and transportation systems. The aim is to apply CST EM STUDIO® (CST EMS) to the optimization of two conflicting...
